Mut Monitor Version 2.0 Released 12/04/2009 - Page 3 - MyRollingRoad & South West Mitsubishi EVO Forums

CLaNZeR · 18-04-2009, 01:55 PM

Find attached Mut Monitor Version 2.04

I have added the 2 byte reply for the custom commands so people that have done the 2 byte mod to their ECU's can test it and see if they get a reply.

I have not added the calculations, so you will get the raw replies.

The calculations below are take from Evoscan

Request ID's are

00 = ECU Load 0.3125 * Result
02 = RPM 1000 * Result /256
04 = Airflow 6.29 * Result /64

If I have got it right then will add option to main ECU monitoring Tab.

Cheers

Sean.

nads1978 · 18-04-2009, 07:02 PM

Hi, okay had 1/2 hr spare today so tried 2.04

Old version 1.x un-installed first.

I only get com ports 5 thru 9 on the drop down.

Tried with my 1.3 cable, and your cable also.

Worked with version 1.x (1.8 I think). But now nothing.

Tried EcuFlash - connects okay with the 1.3 cable but your cable does not connect with yours (Is it supposed to? - or is it for just MutMonitor?)

Cheers.

CLaNZeR · 18-04-2009, 07:08 PM

Quote:

Originally Posted by nads1978

Hi, okay had 1/2 hr spare today so tried 2.04

Old version 1.x un-installed first.

I only get com ports 5 thru 9 on the drop down.

Tried with my 1.3 cable, and your cable also.

Hi mate

Beat ya Space Invaders score by the way

Sounds like either your cables are setup for high ports (beyond 10) or the ports are locked by another process.

In Device Manager what ports does it show when your Clanzer FTDI is plugged in and also when the OP1.3 is plugged in?

The Clanzer FTDI 232B cable will not work with ECUflash.

Might be worth a re-boot of your machine to clear the ports and try again.

Cheers

Sean.

nads1978 · 18-04-2009, 07:11 PM

Quote:

Originally Posted by CLaNZeR

Beat ya Space Invaders score by the way

Quote:

Originally Posted by CLaNZeR

Might be worth a re-boot of your machine to clear the ports and try again.

Yeah, will try reboot and have another go tomorrow.

It has been a week or so since turned it off!

CLaNZeR · 18-04-2009, 07:20 PM

Nads you are so competitive, I can see your online status as playing Space Invaders

Next it will be the track

nads1978 · 18-04-2009, 07:52 PM

GGGGGGGGGaaaaaaaaaaaaaaa so close.

thief99 · 19-04-2009, 10:44 AM

Dear ClaNzer.
i have 98 eclipse turbo.i build cable by myslef. The cable can work with MitsuLogger OK.But can't work with mutmonitor.Please help me to verify the problem.
The status log show "Error was expecting 0x00 0x55 0xEF 0x85 but receive 0x00 0x55 0x3f 0x0".
Can you give me some advice.thanks
attach file is pic catch from my PC

CLaNZeR · 19-04-2009, 06:10 PM

Quote:

Originally Posted by thief99

Dear ClaNzer.
i have 98 eclipse turbo.i build cable by myslef. The cable can work with MitsuLogger OK.But can't work with mutmonitor.Please help me to verify the problem.
The status log show "Error was expecting 0x00 0x55 0xEF 0x85 but receive 0x00 0x55 0x3f 0x0".
Can you give me some advice.thanks
attach file is pic catch from my PC

Hi thief99

I am sure the Init reply for the Mut protocol should be the same for all vehicles that support it. I suppose it could be different but I have no way of testing that.

If it is meant to be the same then it does seem as the data that is being read back could be corrupt or it could be down to unicode problems again.

What are the regional settings on your computer?

Cheers

Sean.

thief99 · 20-04-2009, 01:17 AM

Quote:

Originally Posted by CLaNZeR

Hi thief99

I am sure the Init reply for the Mut protocol should be the same for all vehicles that support it. I suppose it could be different but I have no way of testing that.

If it is meant to be the same then it does seem as the data that is being read back could be corrupt or it could be down to unicode problems again.

What are the regional settings on your computer?

Cheers

Sean.

HI,CLaNZeR
my pc regional settings is "traditional chinese".
thanks for your reply.

And · 20-04-2009, 07:52 AM

Hi Sean

Don't worry about sending it back yet, looks like you'll still need it, are you going to Japfest? maybe we can exchange then?

Thanks
Andy

CLaNZeR · 20-04-2009, 04:47 PM

Quote:

Originally Posted by thief99

HI,CLaNZeR
my pc regional settings is "traditional chinese".
thanks for your reply.

Hi could you change it to English and try again.

I think this could again be a Unicode problem.

Cheers

Sean.

CLaNZeR · 20-04-2009, 04:50 PM

Quote:

Originally Posted by And

Hi Sean

Don't worry about sending it back yet, looks like you'll still need it, are you going to Japfest? maybe we can exchange then?

Hi Andy

Many thanks for that mate, I try and find time this weekend to get the other stuff out of the way with it and pop it in the post.
Not going to make Japfest, too much on as usual

Could you PM over your address mate

And a huge thanks again for helping out.

Cheers

Sean.

thief99 · 22-04-2009, 01:14 AM

HI CLaNZeR
I will change region setting to English at this weekend.
And report the result.
thanks

criptballer · 13-05-2009, 05:08 AM

Ok, so I must retarded because I tried downloading the zip file 2.0 and when i installed it i got "run time error 380, A script engine for the specified language can't be created" Am I doing something wrong here? also, a guy from vividracing.com who is helping tune my evo X said that some people have been having good luck with the MUT 1.5 and he sent me it. I tried it and while it did install fine, it didn't read my op2.0, after doing some reading i'm going to try and find which port my computer is reading it under and will see if it works. Is there any way of downgrading the firmware of my op2.0 to maybe make it work? thanks guys

criptballer · 13-05-2009, 05:02 PM

bump^......

CLaNZeR · 13-05-2009, 06:12 PM

Quote:

Originally Posted by criptballer

Ok, so I must retarded because I tried downloading the zip file 2.0 and when i installed it i got "run time error 380, A script engine for the specified language can't be created" Am I doing something wrong here? also, a guy from vividracing.com who is helping tune my evo X said that some people have been having good luck with the MUT 1.5 and he sent me it. I tried it and while it did install fine, it didn't read my op2.0, after doing some reading i'm going to try and find which port my computer is reading it under and will see if it works. Is there any way of downgrading the firmware of my op2.0 to maybe make it work? thanks guys

Hi

Have you changed your Regional settings to English? as mentioned in this thread.

Also Make sure you download and install version 2.0 first
http://www.myrollingroad.com/attachm...5&d=1239571521

Then update the files by overwriting them with version 2.04
http://www.myrollingroad.com/attachm...8&d=1240062669

This should work with OP2.0

What Car are you trying it on.

Cheers

Sean.

criptballer · 13-05-2009, 08:37 PM

well i don't have to change my settings to English because i live in the U.S. and yeah i tried installing the 2.0 version first but when i open the .exe file that error comes up.

what should i do?

thanks

CLaNZeR · 14-05-2009, 10:03 AM

Quote:

Originally Posted by criptballer

well i don't have to change my settings to English because i live in the U.S. and yeah i tried installing the 2.0 version first but when i open the .exe file that error comes up.

what should i do?

thanks

First time I have heard of someone getting a runtime error 380 and doing a search on the web, it does seem to point to device drivers rather than the VB runtime modules.

One of those difficult ones to try and debug when I am not sitting at your computer

Have you tried it on another machine?

Also you did not answer to what car you were trying to Log on, if it is a EVO X then it will not work anyway as the Can Protocol has not been implemented yet

Cheers

Sean.

Engineer · 03-07-2009, 10:14 AM

No connection with MMC RVR '94.
MUT Monitor can't change baudrate to 15625.
Using Jeff scheme.
Anybody can help to me?

jannerboy · 13-07-2009, 09:24 PM

Hi Sean,
Before I start to play I have a couple of queries?
EVO VI with a Ralliart ECU.
Tactrix OP2.0 Rev D.
I also have an additional white block connector that plugs into the Tactrix and a connector next to the OBDII port. Do I need to plug this connector in for the Mut Monitor to work?
I will short pins 1 and 4 tomorrow night and test this lot out!

John.

jannerboy · 14-07-2009, 08:19 PM

well IT WORKS!
the most important bit was to connect pins 1 and 4 together.
a few lights flash on the dashboard (ABS prob not work)...
but it works.

if only i could get ECUFlash to work with the Tactrix OP2.0

Sean, are u going to develop this further? can i help?

John

CLaNZeR · 14-07-2009, 08:47 PM

Quote:

Originally Posted by jannerboy

Sean, are u going to develop this further? can i help?

Hi John

At the moment I just have not got time to take it any further.

I work away from home 5 days a week and struggle to find time to do all my hobby stuff.

I had a period off work from Dec- Feb and hence why the time to develop Mutmonitor and the test circuits.

Now I struggle to even play with the stuff myself. I also play with Magnets and replicating people that come along with perpetual motion/Free Energy claims and my other site http://www.overunity.org.uk takes up the spare time at the moment.

Also if truthfull, not had that much feedback on the MutMonitor software or cables I have designed and released. So do not know if the on going effort is worth it.

Thanks for the feedback though

Cheers

Sean.

acamus · 15-07-2009, 05:38 AM

Quote:

Originally Posted by Engineer

No connection with MMC RVR '94.
MUT Monitor can't change baudrate to 15625.
Using Jeff scheme.
Anybody can help to me?

I believe on pre-1996 versions only ALDL interface with 1953 baud rate is possible.

Engineer · 15-07-2009, 10:17 AM

Quote:

Originally Posted by acamus

I believe on pre-1996 versions only ALDL interface with 1953 baud rate is possible.

No good...

And what software can i use to diagnose MMC?
Note: MMC RVR Japanese, not European or American

acamus · 15-07-2009, 12:48 PM

http://mmcdlogger.sourceforge.net
http://students.db.erau.edu/~szabafab/stein/
http://www.technomotive.com/prod/datalog/datalogger.htm

Engineer · 16-07-2009, 05:54 AM

Thank you, acamus.
But.... I know about your posted links, and about software on there sites. I have 16 pin connector, no 14 pin!
The same car, like my car, scanned successfully by Chinese scanner Launch X-431 by this 16 pin connector!
Variations: I use Jeff Interface on a real COM port, no virtual. In logging of COM1 i'm find an error on changing baudrate!!! When i connect USB cable (chip ARK3116) from mobile phone, baudrate is changed, no error!

What can i connect a pinouts from Jeff interface (PC side) to pinouts from USB cable? All needed pinouts on cable enabled.
Thanks for all.

Sorry for my English, i'm Russian

acamus · 20-07-2009, 11:45 AM

Sorry I cannot help you more,
connector does not play any role in communication protocol IMHO.